# Inline Bearing Block

{% hint style="info" %}
This product is packaged with the 3/4" Radial Bearing. If different bearings are needed visit our [Ball Bearings Product Page](https://wcproducts.com/collections/cnc-hardware/products/ball-bearings).
{% endhint %}

## Assembly Instructions

The following page show the General Assembly Instructions for the Inline Bearing Block. The appropriate images for the three configurations will be shown side by side.

{% hint style="success" %}
Vibra-TITE VC-3 Threadmate ([Vibra-TITE](https://wcproducts.com/products/threadlocker)) is recommended on all bolts that thread into a tapped hole.
{% endhint %}

## Step 1

Slide all the appropriate bearings and washers on to the Dowel Pin. The table below lists the number of washers used for each bearing configuration.

{% hint style="info" %}
If you are using 1/2” and 5/8” bearings instead of the standard 3/4” bearings, you can substitute in 0.03” washers to cut down on the part count.
{% endhint %}

| Bearing Size | 0.01” Washer QTY |
| :----------: | :--------------: |
|    1/2” OD   |        20        |
|    5/8” OD   |        18        |
|    3/4” OD   |         4        |

{% tabs %}
{% tab title="1/2" Bearings" %}

<figure><img src="https://3321970383-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvpVKG4kVLnIlJUReyy4N%2Fuploads%2FChGu7YcUWRKj2vLBtg1u%2FInline%20Bearing%20Block%20-%20Step%201a.svg?alt=media&#x26;token=41342841-9394-4cf6-9110-d10ce4a9eb93" alt="" width="563"><figcaption></figcaption></figure>
{% endtab %}

{% tab title="5/8" Bearings" %}

<figure><img src="https://3321970383-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvpVKG4kVLnIlJUReyy4N%2Fuploads%2FyDUT5I53tmPQfM0stIEL%2FInline%20Bearing%20Block%20-%20Step%201b.svg?alt=media&#x26;token=9a7b58c4-bd7d-4619-8f9b-6ca89d6ab185" alt="" width="563"><figcaption></figcaption></figure>
{% endtab %}

{% tab title="3/4" Bearings" %}

<figure><img src="https://3321970383-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvpVKG4kVLnIlJUReyy4N%2Fuploads%2FkNUJ4bdLfE9gSTpYLblG%2FInline%20Bearing%20Block%20-%20Step%201c.svg?alt=media&#x26;token=ce2c533d-630f-4919-a29b-f54d9cec8388" alt="" width="563"><figcaption></figcaption></figure>
{% endtab %}
{% endtabs %}

## Step 2

Slide the assembly from Step 1 into the Bearing Block. The bearing and washers should all fit in the slots on the block. The dowel pin will be constrained by the Shoulder Bolts and 3D Printed Spacers installed in Step 3.

{% tabs %}
{% tab title="1/2" Bearings" %}

<figure><img src="https://3321970383-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvpVKG4kVLnIlJUReyy4N%2Fuploads%2Fn1lvB46x1j6FXgEIoxsJ%2FInline%20Bearing%20Block%20-%20Step%202a.svg?alt=media&#x26;token=d2249b32-343b-4e72-bb0e-165cec6b0ca1" alt="" width="563"><figcaption></figcaption></figure>
{% endtab %}

{% tab title="5/8" Bearings" %}

<figure><img src="https://3321970383-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvpVKG4kVLnIlJUReyy4N%2Fuploads%2Fno5wRU0SYdc6c9ycjYxu%2FInline%20Bearing%20Block%20-%20Step%202b.svg?alt=media&#x26;token=0cd1818d-978a-42f1-a04f-e56c72a2068a" alt="" width="563"><figcaption></figcaption></figure>
{% endtab %}

{% tab title="3/4" Bearings" %}

<figure><img src="https://3321970383-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvpVKG4kVLnIlJUReyy4N%2Fuploads%2FKl8BJibTT12XtyUhAWy4%2FInline%20Bearing%20Block%20-%20Step%202c.svg?alt=media&#x26;token=ee397fcc-4530-4961-b706-8fe9604fdd7f" alt="" width="563"><figcaption></figcaption></figure>
{% endtab %}
{% endtabs %}

## Step 3

Bolt the bearing and spacer stack-up to the block as shown in the images below. The sizes of the spacers required for each bearing configuration is listed in the table below.

{% hint style="info" %}
The 1/2” Bearing Configuration does not require an Aluminum Spacer.
{% endhint %}

| Bearing Size | 3D Printed Spacer Length | Aluminum Spacer Length |
| :----------: | :----------------------: | :--------------------: |
|    1/2” OD   |           1/8”           |           N/A          |
|    5/8” OD   |           3/16”          |          1/16”         |
|    3/4” OD   |           1/4”           |          1/8”          |

{% tabs %}
{% tab title="1/2” Bearings" %}

<figure><img src="https://3321970383-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvpVKG4kVLnIlJUReyy4N%2Fuploads%2F7jw0YgDvYJxedbSE1NlW%2FInline%20Bearing%20Block%20-%20Step%203a.svg?alt=media&#x26;token=1c7e38d4-b553-4257-8a9f-6db5af7d3695" alt="" width="563"><figcaption></figcaption></figure>
{% endtab %}

{% tab title="5/8” Bearings" %}

<figure><img src="https://3321970383-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvpVKG4kVLnIlJUReyy4N%2Fuploads%2FH6wXQerQWzG9271F8rtZ%2FInline%20Bearing%20Block%20-%20Step%203b.svg?alt=media&#x26;token=0c12e5cd-ad00-4d86-b25c-230eeccf907e" alt="" width="563"><figcaption></figcaption></figure>
{% endtab %}

{% tab title="3/4” Bearings" %}

<figure><img src="https://3321970383-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvpVKG4kVLnIlJUReyy4N%2Fuploads%2FWON3xhkItkIvm5utsRtw%2FInline%20Bearing%20Block%20-%20Step%203c.svg?alt=media&#x26;token=15588eed-e600-4168-b588-13401cf02be0" alt="" width="563"><figcaption></figcaption></figure>
{% endtab %}
{% endtabs %}