# Steps 1-6

{% hint style="success" %}
Vibra-TITE VC-3 Threadmate ([Vibra-TITE](https://wcproducts.com/products/threadlocker)) is recommended on all bolts that thread into a tapped hole.
{% endhint %}

## Step 1

Press the 1/2" Rounded Hex bearing into the Shooter Side Plate. Repeat this step for the other side. Be sure to press the bearing in from the opposite side so that the bearing flanges are on opposite sides of the plates. 

Secure the bearing using a Bearing Retention Plate and a Bearing Roller Center Plate.

<figure><img src="/files/N9z1XTYUlhS7iuzTSeSP" alt=""><figcaption></figcaption></figure>

## Step 2

Press the 1/2" Rounded Hex bearing into the Shooter Hood Plate. Repeat this step for the other side. Be sure to press the bearing in from the opposite side so that the bearing flanges are on opposite sides of the plates.&#x20;

Secure the bearing using a Bearing Retention Plate and a Bearing Roller Center Plate.

{% hint style="info" %}
The image below only shows the Right Configuration of the hood plate, the same applies to the Left configuration.
{% endhint %}

<figure><img src="/files/JflcbeSzocPXT0KDMHC0" alt=""><figcaption></figcaption></figure>

## Step 3

Press two 7"L Standoffs into the Printed Fixed Hood.&#x20;

Due to varying print settings, this standoff could be a press fit. In such case a dead blow hammer or arbor press can be used to install these standoffs.

{% hint style="warning" %}
The Printed Hood **is not included** with the GreyT Shooter. Teams must print this using their preferred settings.

The file below is for the **default Fixed Hood**. Teams may choose to modify this as needed.
{% endhint %}

{% file src="/files/xycRN3Tt1fDR0BuW8n4v" %}

<figure><img src="/files/0BBf7D353ZP8ZkRaAzFJ" alt=""><figcaption></figcaption></figure>

## Step 4

Attach the Shooter Side Plates from Step 1 to the Hood assembly from Step 3 using #10-32 x 3/4"L bolts.

<figure><img src="/files/She2t83ubCLWqxOndUeX" alt=""><figcaption></figcaption></figure>

## Step 5

Bolt the front of the Shooter together using the Standoff & Spacer stack up shown below.

{% hint style="info" %}
Do not forget to install 3/4"L spacers between the 7"L Standoffs and Shooter Side Plates on one side.
{% endhint %}

<figure><img src="/files/loN3lXxHxBp4JTmDD4Xo" alt=""><figcaption></figcaption></figure>

## Step 6

Attach the Hood Plates from Step 2 to the assembly from Step 5 using #10-32 x 1-1/4"L and 3/4"L Spacers.

<figure><img src="/files/4sWKsJeIG0lKb5FxbGkz" alt=""><figcaption></figcaption></figure>


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://docs.wcproducts.com/welcome/greyt/greyt-shooter-4-6/assembly-instructions/shooter-base-with-fixed-hood/steps-1-6.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.