# Getting Started

## Assembly Prep

Refer back to the [Individual Components](/welcome/greyt/greyt-shooter-4-6/general-info/individual-components.md) page to ensure that all necessary parts are located before starting assembly steps.

#### Tools Required For Assembly

These tools are required for the assembly of the GreyT Shooter (4"-6").

* SAE/Inch Allen Set
* 3/8” Hex Wrench
* Drill w/ Drill Bit Set

{% hint style="success" %}
Vibra-TITE VC-3 Threadmate ([Vibra-TITE](https://wcproducts.com/products/threadlocker)) is recommended on all bolts that thread into a tapped hole.
{% endhint %}

## Key Assembly Instructions 

The following pages cover the basic assembly instructions for the GreyT Shooter (4"-6").

<table data-view="cards"><thead><tr><th></th><th></th><th data-hidden data-card-cover data-type="image">Cover image</th><th data-hidden data-card-target data-type="content-ref"></th></tr></thead><tbody><tr><td><strong>Shooter Base - Fixed Hood</strong></td><td>Assembly Instructions</td><td><a href="/files/A1qOqix9cgtp1DRwdyr1">/files/A1qOqix9cgtp1DRwdyr1</a></td><td><a href="/pages/moFgyTLoSkgxpXElJPkA">/pages/moFgyTLoSkgxpXElJPkA</a></td></tr><tr><td><strong>Shooter Base - Actuator</strong></td><td>Assembly Instructions</td><td><a href="/files/xNqDpoMbcYSDqgv1SY29">/files/xNqDpoMbcYSDqgv1SY29</a></td><td><a href="/pages/gZRrMrAU5IJhCzrPb70a">/pages/gZRrMrAU5IJhCzrPb70a</a></td></tr><tr><td><strong>Additional Hardware</strong></td><td>Assembly Instructions</td><td><a href="/files/mLGeN4mD4G61m5ivQSXm">/files/mLGeN4mD4G61m5ivQSXm</a></td><td><a href="/pages/80KrtigxA6C4T6OdtlBG">/pages/80KrtigxA6C4T6OdtlBG</a></td></tr></tbody></table>

## Hex Shaft Cut Lengths

The overall length for the hex shafts does not need to be precise. Cutting to length with a hacksaw is acceptable if that is the only available option. Cutting to length and then using a lathe to clean up both ends is the recommended method.&#x20;

{% hint style="info" %}
The shaft lengths below allow for either a bolt ([WCP-0571](https://wcproducts.com/products/bolts)) or 1/2" Hex Shaft Collars ([WCP-0324](https://wcproducts.com/products/clamping-shaft-collars)) can be used
{% endhint %}

<figure><img src="/files/kyZ9Q34yhv9KZKMK8YYl" alt=""><figcaption></figcaption></figure>


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://docs.wcproducts.com/welcome/greyt/greyt-shooter-4-6/assembly-instructions/getting-started.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.