# Steps 1-5

{% hint style="success" %}
Vibra-TITE VC-3 Threadmate ([Vibra-TITE](https://wcproducts.com/products/threadlocker)) is recommended on all bolts that thread into a tapped hole.
{% endhint %}

## Step 1

Mount the Limelight onto the Shooter Base using #10-32 x 2"L bolts and #10-32 Nuts as shown below.

<figure><img src="https://2259054670-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvrmoJXaaJXScDmJVtbba%2Fuploads%2Ftm6g9YibRcLRcfcANCm7%2F4in%20-%206in%20GreyT%20(Additional%20Hardware)%20-%20Step%201.svg?alt=media&#x26;token=faf5ac45-1d49-4dc7-b3e9-38feb03ef21c" alt=""><figcaption></figcaption></figure>

## Step 2

Slide the cut shooter wheel shaft into position .

{% hint style="info" %}
The image below uses the 4" OD x 1.5" WD Colson Performa Wheels (WCP-1533) with the Colson Live Hub (WCP-0809). The spacer stack up is for this configuration only. Using different wheels might change the spacer stack up needed.
{% endhint %}

{% tabs %}
{% tab title="Shaft Install" %}

<figure><img src="https://2259054670-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvrmoJXaaJXScDmJVtbba%2Fuploads%2FVmrkWneTZFzgk3h2T3n4%2F4in%20-%206in%20GreyT%20(Additional%20Hardware)%20-%20Step%202A.svg?alt=media&#x26;token=b5f900bf-cb41-40fd-bd33-5f609f6e41cb" alt=""><figcaption></figcaption></figure>
{% endtab %}

{% tab title="Spacer Locations" %}
{% hint style="info" %}
This stack up is only applicable when using the Colson Wheel and Hub combination called out above.&#x20;

Changing the shooter wheel will affect the spacers needed.
{% endhint %}

<figure><img src="https://2259054670-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvrmoJXaaJXScDmJVtbba%2Fuploads%2FXli5YkGGsYLZ8sBIEJk6%2F4in%20-%206in%20GreyT%20(Additional%20Hardware)%20-%20Step%202B.svg?alt=media&#x26;token=2bcb646e-4b08-4fd7-bd56-e6fbb33eca8c" alt=""><figcaption></figcaption></figure>
{% endtab %}
{% endtabs %}

## Step 3

Mount a Kraken X60 to the assembly from Step 2 using #10-32 x 3/8"L bolts as shown below.

{% hint style="info" %}
Repeat this step to mount a Kraken X60 on the other Shooter Side Plate.
{% endhint %}

<figure><img src="https://2259054670-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvrmoJXaaJXScDmJVtbba%2Fuploads%2FNe3eKEOTo3jQ5GgVHft7%2F4in%20-%206in%20GreyT%20(Additional%20Hardware)%20-%20Step%203.svg?alt=media&#x26;token=ccf627eb-8ba4-4b65-8f06-4188fa11c8ac" alt=""><figcaption></figcaption></figure>

## Step 4

Install a the belt and pulley onto the motor SplineXS shaft and the driven hex shaft.

{% hint style="info" %}
The image below uses the Bolt Retention configuration of the Hex Shaft as called out by the Hex Shaft Cut Lengths Section.&#x20;

If the Shaft Collar Retention method is preferred, use a 1/2" Hex Clamping Shaft Collar ([WCP-0324](https://wcproducts.com/products/clamping-shaft-collars)).
{% endhint %}

<figure><img src="https://2259054670-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvrmoJXaaJXScDmJVtbba%2Fuploads%2Fp0BwZPEdk2ZjZOCANVyZ%2F4in%20-%206in%20GreyT%20(Additional%20Hardware)%20-%20Step%204.svg?alt=media&#x26;token=3c26de6b-0f1e-49ff-9927-ab074bf73fb3" alt=""><figcaption></figcaption></figure>

## Step 5

Mount 1-1/4"L Nutstrips to the Shooter Base using #10-32 x 3/8"L bolts.&#x20;

{% hint style="info" %}
The mounting location of these Nutstrips will vary on the desired final mounting location.
{% endhint %}

{% hint style="success" %}
This is the last step needed for the Fixed Hood Configuration of the GreyT Shooter.
{% endhint %}

<figure><img src="https://2259054670-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvrmoJXaaJXScDmJVtbba%2Fuploads%2FPMmp8sM2MkZvTzUclt43%2F4in%20-%206in%20GreyT%20(Additional%20Hardware)%20-%20Step%205.svg?alt=media&#x26;token=7078d421-519b-4c6d-b648-83af4273cf27" alt=""><figcaption></figcaption></figure>

## Step 6

Mount the desired Linear Actuators as shown below using the called out M4 hardware.

{% hint style="info" %}
This Step is only applicable to the Linear Actuator configuration of the GreyT Shooter.
{% endhint %}

{% file src="<https://2259054670-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvrmoJXaaJXScDmJVtbba%2Fuploads%2Fva0IUCOXhXflgMRXvYFv%2FWCP-0604-009.STEP?alt=media&token=2c82456d-4a49-4107-a9bf-5934dda1644f>" %}

{% file src="<https://2259054670-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvrmoJXaaJXScDmJVtbba%2Fuploads%2FF0HG5JqjZxpb6gQMP6ZX%2FWCP-0604-010.STEP?alt=media&token=ccc8b55b-418f-41bd-b427-2f714741e661>" %}

<figure><img src="https://2259054670-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FvrmoJXaaJXScDmJVtbba%2Fuploads%2Fxmw28Ws00NUDw5HnLFyG%2F4in%20-%206in%20GreyT%20(Additional%20Hardware)%20-%20Step%206.svg?alt=media&#x26;token=cf6a9b18-0f38-4f49-af07-e5baf09722da" alt=""><figcaption></figcaption></figure>