# Extra Stage

{% hint style="info" %}
This section is only needed for 3+ Elevator assemblies.
{% endhint %}

{% hint style="success" %}
Vibra-TITE VC-3 Threadmate ([Vibra-TITE](https://wcproducts.com/products/threadlocker)) is recommended on all bolts that thread into a tapped hole.
{% endhint %}

<figure><img src="https://4232247706-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FGkl0O36xcwVLQSec7nzx%2Fuploads%2FZ368egGjwvy7au4EwJwr%2FExtra%20Stage%20-%20Cover.svg?alt=media&#x26;token=bf0ce7cd-179b-46b3-8c39-01885831dfd6" alt="" width="300"><figcaption></figcaption></figure>

## Step 1

Before assembling the Extra Stage Horizontal Tube, drill the threaded holes on the Aluminum Tube Plugs marked in green. Both sides must be drilled. Then, assemble the Extra Stage Horizontal Tube as shown in the image below.

{% hint style="info" %}
The bolt heads for both Pulley Blocks must be facing towards each other.
{% endhint %}

<figure><img src="https://4232247706-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FGkl0O36xcwVLQSec7nzx%2Fuploads%2F2JnpDeRE5X1meuNwGezE%2FExtra%20Stage%20-%20Step%201.svg?alt=media&#x26;token=2868b95b-ba92-4d3b-97f8-d0553da89b57" alt="" width="563"><figcaption></figcaption></figure>

## Step 2

Assemble the Extra Stage Cross Tube as shown in the image below. Make sure not to crush the tube when tightening the #10-32 x 1-1/4"L bolts.

<figure><img src="https://4232247706-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FGkl0O36xcwVLQSec7nzx%2Fuploads%2FCcelTdR98Rp2tkVgtYzy%2FExtra%20Stage%20-%20Step%202.svg?alt=media&#x26;token=578ec6db-f9bf-4c7b-b67a-c23413a9b49a" alt="" width="563"><figcaption></figcaption></figure>

## Step 3

Bolt the Extra Stage Vertical Tubes to the assembled Extra Stage Horizontal Tube. When assembled, the heads of the #10-32 x 1-1/2"L bolts will sit inside the Elevator Block.

{% hint style="info" %}
Make sure to install the Bearing Blocks with only one of the 3/4" OD Radial Bearings.&#x20;
{% endhint %}

<figure><img src="https://4232247706-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FGkl0O36xcwVLQSec7nzx%2Fuploads%2FoAokjVVr1izQMcq8R2Eo%2FExtra%20Stage%20-%20Step%203.svg?alt=media&#x26;token=1cb13fa1-42c5-4f1c-a542-4aaa090f0714" alt="" width="563"><figcaption></figcaption></figure>

## Step 4

Attach the assembled Extra Stage Cross Tube to the Extra Stage using four #10-32 x 5"L Bolts and 2-1/2"L Spacers. While it can be lower, it is recommended to mount it as high as possible to increase the strength of the Extra Stage.

<figure><img src="https://4232247706-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FGkl0O36xcwVLQSec7nzx%2Fuploads%2FkWlRnILVPbBhLLL3Apum%2FExtra%20Stage%20-%20Step%204a.svg?alt=media&#x26;token=15fcf27d-54ea-4281-92eb-c5876122caa5" alt="" width="563"><figcaption></figcaption></figure>

<figure><img src="https://4232247706-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FGkl0O36xcwVLQSec7nzx%2Fuploads%2FCKP2JWNmwyE1YzciSeD0%2FExtra%20Stage%20-%20Step%204b.svg?alt=media&#x26;token=12987268-78fc-42a4-a24e-bf78ed4d2c7d" alt="" width="563"><figcaption></figcaption></figure>

## Step 5

Mount both Chain Attachment Brackets to the bottom Extra Stage Horizontal Tube in the orientation shown below. The brackets will be installed using six #10-32 x 2-1/2"L bolts and #10-32 nuts.

{% hint style="info" %}
If you are assembling an elevator with 4 or more stages, these brackets only have to be mounted to the 1st stage after the Elevator Mast.
{% endhint %}

<figure><img src="https://4232247706-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FGkl0O36xcwVLQSec7nzx%2Fuploads%2Fj36M6HvjZ4Pch7l2PG28%2FExtra%20Stage%20-%20Step%205.svg?alt=media&#x26;token=47ecd43c-f5af-4c99-9e68-d5a8c26f92e1" alt="" width="563"><figcaption></figcaption></figure>