# Step 10-12

{% hint style="success" %}
Vibra-TITE VC-3 Threadmate ([Vibra-TITE](https://www.vibra-tite.com/threadlockers/removable-reusable-threadlockers/vibra-tite-vc-3-threadmate/?gad_source=1\&gad_campaignid=89842748\&gbraid=0AAAAAD2P3YRFs-3Kj4YTX9A4qtZWYdqGQ\&gclid=EAIaIQobChMI0JSks4upjQMVcNPCBB1_ghB9EAAYASAAEgJQp_D_BwE)) is recommended on all bolts that thread into a tapped hole.
{% endhint %}

## Step 10

The magnet will come installed in the Sensor Shaft. 

Slide all gears and shafts into position. For the Gears Below configurations, the 1/4” ID 3D Printed Spacer is required on the Sensor Shaft. 

The Encoder Belt will be installed during this step. This can be done by placing it on the 3D Printed Sensor Pulley, and then sliding it onto the 3D Printed Rotation Pulley installed in Step 8.

<figure><img src="/files/dqvuu44hWvyDk51fEpO2" alt=""><figcaption></figcaption></figure>

## Step 11

Bolt together the assemblies from steps 8 and 9 as shown in the images below. For all configurations, the bolt locations are marked in green and orange in the images below.

The table below indicates what length bolt and spacer is required in each position for each configurations colored markers.

{% hint style="info" %}
For all bolt locations marked in orange, the bolt must be spaced away from the bottom plate with a 1/8"L Spacer. This is to keep the end of the bolt from colliding with the drive idler gear in the Gears Above and Gears Below configurations.
{% endhint %}

<table><thead><tr><th width="156">Configuration</th><th>Green Bolt</th><th>Green Spacer</th><th>Orange Bolt</th><th>Orange Spacer</th></tr></thead><tbody><tr><td>Gears Below</td><td>1-3/4"</td><td>1-7/8"</td><td>1-3/4"</td><td>1-1/8"</td></tr></tbody></table>

<div><figure><img src="/files/tUbql2vAgCCh2vA93Yi2" alt=""><figcaption></figcaption></figure> <figure><img src="/files/D6s74CKCxn1nl8CEpWPy" alt=""><figcaption></figcaption></figure></div>

## Step 12

Install the CTRE Mag Encoder Mount using two #10-32 x 1/2”L bolts. To install the Mag Encoder, remove the board from the case and fit it into the cutout on the 3D Printed Mag Mount. Use the mounting bolts from the Mag Encoder to attach the sensor. The CANcoder can be used as a drop in replacement.

{% hint style="info" %}
While the image below may show the Non-Flipped configuration, this step is the same for all Swerve X configurations.
{% endhint %}

<figure><img src="/files/akE34uO84WzSsMGB6Zv7" alt=""><figcaption></figcaption></figure>


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://docs.wcproducts.com/welcome/gearboxes/wcp-swerve-x/misc/other-configurations/getting-started/flipped-gears-below/step-10-12.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.