# Step 6-9

{% hint style="success" %}
Vibra-TITE VC-3 Threadmate ([Vibra-TITE](https://wcproducts.com/products/threadlocker)) is recommended on all bolts that thread into a tapped hole.
{% endhint %}

## Step 6

The 1/4” ID x 5/8” OD bearing can be pressed into the Wheel Module Fork by hand. Only the Fork that aligns with the Wheel Module Drive Shaft needs a bearing. Once the bearing is in place, use the #10-32 x 1 3/4”L bolts to install both forks into the module.

{% hint style="info" %}
If you ordered your Wheel Module Forks after 5/16/2023, make sure an updated Wheel Module Fork is used on the side with the 15T Bevel Gear. The updated Wheel Module Fork will have a pocket designed to fit a 1/4-20 Nut machined into the outside face.
{% endhint %}

<figure><img src="/files/dJ4seXKJXYo6O6w2L4Nx" alt=""><figcaption><p>Updated Wheel Module Fork</p></figcaption></figure>

<figure><img src="/files/RLuKjAqUlqPvrPb1rl7d" alt=""><figcaption></figcaption></figure>

## Step 7

The Main Drive Shaft and corresponding gear should be installed before the 3D Printed Rotation Pulley. Use the #4-40 x 3/4”L bolts to install the 3D Printed Rotation Pulley.

{% hint style="info" %}
The 3D Printed Rotation Pulley was updated to strengthen the part and allow for longer bolts. If your 3D Printed Rotation Pulley does not have a step at the bottom of the integrated spacers that nests in the 72T Main Rotation Gear, then install the pulley using #4-40 x 3/4"L bolts.
{% endhint %}

{% hint style="warning" %}
Do NOT overtighten the #4-40 bolts, as this will crush the 3d printed part.
{% endhint %}

<figure><img src="/files/U4D4tUaSqRe3c6VUX8is" alt="" width="500"><figcaption></figcaption></figure>

## Step 8

For the Flipped Belt and Flipped Gears Above configurations, the motors are installed using #10-32 x 1/2”L bolts.

{% hint style="info" %}
The motor shaft length does not matter in the assembly of any of the Flipped Swerves.
{% endhint %}

<figure><img src="/files/j8T3w1nyyND2LcPfiUJp" alt=""><figcaption></figcaption></figure>

## Step 9

The magnet will come installed in the Sensor Shaft. &#x20;

The Encoder Belt will be installed during this step. This can be done by placing it on the 3D Printed Sensor Pulley, and then sliding it onto the 3D Printed Rotation Pulley installed in Step 7.

{% hint style="info" %}
For the Belt configuration, the excess 1/4” shoulder on the Sensor Shaft that extends past the Swerve X Bottom Plate can be cut off. However, doing so will prevent the Sensor Shaft from being reused in all other configurations.
{% endhint %}

<figure><img src="/files/0NH2p2CIJIrDRNDTUdQU" alt=""><figcaption></figcaption></figure>


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://docs.wcproducts.com/welcome/gearboxes/wcp-swerve-x/misc/other-configurations/getting-started/flipped-belt/step-6-9.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.